OMNI OH110 Amphibious Rescue Helicopter

Omni International Industries OH110 Medium Amphibious SAR Helicopter.

"Where others fail, OMNI excels."

The OH110 is designed as a easy to fly high speed medium Search and Rescue amphibious helicopter.

Features:

-High speed -150kt+ cruise
-Turbine
-200km+ Range
-GPS map – OmniMap+ with Nav, beacon finder, radio direction finder and radar
-Autopilot – Heading hold, waypoint hold, and heading hold with cruise and hover modes
-Lights – Nav, Landing, Strobe, Beacon, Interior
-Annunciator panel
-Communication radio
– Artic ready
-Dual harness rescue winch
-OmniSling Compatible
-OmniBucket Compatible
-Automatic rotor brake.
-Remote rotor folding from cockpit.
-Amphibious

Operating instructions:
1. Overhead panel: Master switch and Avionics switch: On
2. Overhead panel: Engine On/Off and Throttle Idle/Flight (If rotor brake is turned on it is automatic and needs no further interaction, engines will not start if rotor is folded. Rotor can’t be folded if the rotor is spinning.)
3. Wait for RPM to reach >90% (RPM light will turn off)
4. W/S for pitch, A/D for roll, Up/Down for collective, Left/Right for yaw.

**Caution while flying backwards or sideways over 25kts, may become unstable.

**Caution landing/taking off with tailwind, may become unstable if landing with >25kt tailwind. All aircraft should land/takeoff into a headwind when possible.

**Caution: Sliding door may try to kill you, it is subject to stormworks physics jank… extensive testing and design has gone into the door (more time than the entire heli) to remove all murderous tendency.

**Caution: When landing in the water it is best to let it firmly settle, a slight hover at the surface may result in limited bouncing and unsteadyness… again subject to stormworks physics jank…

Use trim to maintain specific forward speeds.
Return all trims to within 0.10 of zero for position hold ability.

Autopilot functions with heading hold (HD) and waypoint hold (WP) in both hover (H) and cruise (C) modes.
Yellow indicates selected but not active.
Red indicates not active.
Green indicates active.
Grey indicates N/A.

Heading hold (HD) will hold current heading and can be adjusted with the +/- touch controls
Waypoint hold (WP) is available after entering waypoint coordinates into the keypad. It will hold bearing to waypoint and switch from Cruise(C) to Hover(H) mode upon approaching the waypoint.

Both Heading hold (HD) and Waypoint hold (WP) will active Altitude hold (ALT) upon activation. Altitude hold (ALT) can be activated or deactivated independently. While Altitude hold (ALT) is active, set altitude can be changed via the +/- touch controls.

When the autopilot is not active it will display current heading and altitude.
Heading hold (HD) will display set heading while active
Waypoint hold (WP) will display bearing to waypoint while active.
Altitude hold (ALT) will display set altitude while active.

Hover (H) will maintain hover
Cruise (C) will maintain forward cruise speed until reaching a waypoint which will then switch mode to Hover(H)

OmniMap+ functions as a GPS nav with waypoint input that also feeds into the autopilot. It also features Emergency beacon finder, Radio Direction Finder, and Radar.
Modes can be changed at the bottom of the screen with the left and right touch arrows between Nav, EBL,RDF.

Radar can be activated on any mode by touching the R on the right side of the screen.

EBL/RDF modes have a "clear" button for resetting the signals. It’s the C on the right side of the screen.

The menu at the top center of the screen allows users to change unit types and set the RDF frequency.

—————————————————-

Join the OMNI Discord server!
https://discord.gg/8fgww37tgN

—————————————————–

* This is based on the Sikorsky SH-3 Sea King but is not meant to be an exact replica.

**Beacon locator inspired by Illy’s and used with permission.

**Uran_Wind’s ZE gyro used as a basis for control system.

**PenguinO’s comm radio

** Ping|Archimaede’s Advanced PFD

*** Do not re-upload

**** All OMNI vehicles are made and tested with HIGH physics settings. Use of any other physics settings is not recommended and will void warranty.