Skymods

Stormworks: Build and Rescue Mods Catalogue

ENDAIR Beluga XL

Uploaded ·

If you liked this item, please rate it up on Steam Workshop page.

Author: EnderPilot

Last revision: 8 Apr, 2021 at 12:44 UTC

File size: 18.26 MB

On Steam Workshop

Description:
ENDAIR Beluga XL

The ENDAIR Beluga XL is a SuperTransport aircraft developed by EPVIN Aviation Company
It has a Top speed of 240 Knots, Has a range of over 1000KM thanks to the new trent 700 engine and 280.000L of fuel spited into 2 tanks. Also features a realistic cockpit!

Tested to be lag and Multiplayer friendly while holding great shape and performance!

it has a huge cargo hold for Special Cargo Transport that can hold up to 3 A321 Cockpit modules!
or you can make your own 3 modules to load the plane with the Custom Pallet!

[Requires modded workshop or custom mission to spawn]

NOTE: PLEASE DO NOT MODIFY OR RE-UPLOAD THIS VEHICLE
COCKPIT FEATURES:
  • Digital Artificial horizon
  • EICAS monitoring system [as featured in a real Airbus]
  • Map
  • Fuel consumption Calculator
  • Radio comutication for both pilots
  • Autopilot, Altitude hold, Roll stabilisation
  • a blackbox and flight tracking channel with frequency set to 19
  • extendable-retractable Flaps
  • extendable-retractable Spoilers
  • extendable-retractable Landing gear
  • Take-Give control to Captain or First Officer
  • Fly By Wire Safety System [as featured in a real Airbus]
  • Evacuation mode
  • Fire supression safety systems
  • 3 hydraulic systems
  • Cabin light and heating controls
  • Nav, Strobe, Landing, Taxi and beacon lights

    If you are getting a master warning check:

  • If you have a fire Warning
  • If you have a failure message in your PFD
  • If you have are stalling
    HOW TO GET IN:
  • You have to go behind the cockpit and press the red button labeled (open door)
    STARTUP PROCEDURE:

    1. Open Battery and avionics
    2. Open All 3 PFD Controllers
    3. Open all Hydraulic systems
    4. Open EN1 and EN2 Fuel cutoff and pumps
    5. Open EN1 and EN2 GEN and BUS
    6. Open EN1 and EN2 Starters
    7. Monitor EICAS Screen until engines are stabilized
    8. Open Beacon

    APU STARTUP PROCEDURE:

    1. Open APU Hydraulic pumps
    2. Open APU Auto-Starter

    AUTOPILOT SETUP:

    Tip Take a moment before takeoff to input your desired coordinates and Altitude to the aircraft!

    1. Set up your waypoint coordinates on the Autopilot Coordinates Panel
    2. Press the Engage Autopilot Button
    3. Enable FD

    ALTITUDE SETUP:

    1. Set up your desired Altitude on the Altitude Hold Panel
    2. Press the ALT HOLD Button
    3. Enable FD

    BLACKBOX AND FLIGHT TRACKING:

    On channel: 19 there is a composite signal transmition that holds flight information

    THROTTLE:

    * 120% Takeoff
    * 120-100% Cruise [Its most eficient at 120%]
    * 55-45% Landing
    * 9-12% Taxiing

    CREDITS

    Thanks to @Thias04 For this Awesome 3D Picture
    3d MAP by Buunuu
    CONSUMPTION 1×1 By krimwand
    4 dials 1 display by michubushimax9
    Advanced PFD by Ping|Archimaede

    Consider leaving a Rating and a Comment if you like the creation.
    If you find any Bugs please report them down below
Download

Tags: